How Many Lines Do You Put On A Baitcaster

Over the years, the amount of line you should put on a fishing reel has been contentious. Some individuals recommend filling it, while others recommend simply half-filling it. How many lines should you add to a baitcasting reel after researching?

The common opinion is to load your reel with enough line to leave a 1/8-inch gap between the line and the spool’s top. You don’t want it to be filled because you’ll never use it all, and you don’t want it to be filled halfway because it didn’t cast well. When you combine this with a high-quality line, you should get the best results.

I tried filling it wholly and halfway and discovered that the sweet spot is around 1/8 of an inch. It was approximately 120 yards to my reel. I usually used a braided line for my main. If you follow the 1/8 inch rule, the results may vary if you use fluorocarbon or monofilament lines.

Which Line Should You Use On Your Baitcaster?

When it comes to fishing line, you have three options:

  1. Fluorocarbon.
  2. Monofilament.
  3. Braided.

It will all depend on what you tend to fish for, but I suggest a braided mainline. I almost always have a leader on end, and if you want your leader to float, use mono. And if you want it to sink, use fluoro. Because the braided line floats, I use fluoro as my leader line.

Braided line is more durable, lasts longer, and has a higher sensitivity. That is why I employ it. Mono comes into play if you’re going to be fishing from the water’s surface. If you need the line to sink slightly, use fluoro.

Why We Should Put A Braided Line On Baitcaster

My primary fishing line on my rods is always braided. It is slightly more expensive, but it lasts remarkably longer. It does not tangle as easily and will not snap if your hook becomes entangled in a tree or weeds (unless your knot-tying skills are subpar).

Many people dislike the braided line because it was shoddy at first when it debuted. It felt almost like wire and was difficult to work with. But it’s come a long way, and I think it’s far superior to anything else.

The following are the primary reasons why I use a braided line:

  • It appears to cast more smoothly than anything else.
  • It is not as easy for birds to nest.
  • If you get snagged on something, it will not break.
  • It is not easy for fish to bite through.
  • It’s much more sensitive, making your rod feel like a higher-end model.

Some people use a straight braided line, but I like it in the center. I will use the regular fishing line as the backing and the normal line as the leader. It is not the best, but it’s the one and the only thing that worked for me in the past.

Do We Need To Put Backing On Baitcaster?

The backing line is the line that is directly attached to the spool beneath your dominant fishing line. If you’ve ever used a fly fishing rod, you’ll know that the normal line goes on first, followed by your fly line. You can do that thing with a baitcaster or almost any other reel type.

I’ve tried putting the braided line directly on the spool, then it worked, but it slipped a little. When I added the backing, it seemed to work well and better. Any ordinary line will suffice because you will never intend to use it. Here’s a video showing the ways how to attach the backing to the braided line:

Then, what are the reasons why you put it on?

I only wrapped the spool a couple of times to cover it. Then I attached my braided line to it and filled it with water. The braided line is a little slick and has difficulty digging into the metal spool (it digs into the fishing line much more effectively). Let’s talk about how to do it now that you know what you need to do.

How Do You Put Line On A Baitcaster?

The first thing you should note is applying some oil to your bearings. Maintaining your reel in good condition is essential, which is why you should clean it regularly. After that, adjust your drag and spool tension.

The following step is to put it on your back. For this, use any aged fishing line. Thread the line through your lowest guide loop, through the small hole on your reel, which has a moving motion from side to side. If you have one above the metal rod, tie it to your spool (make sure the line that goes on the spool remains as it was in the package). Hold the line tight and wrap it a few times (to hide the spool).

Following that, tie your braided line to the backing. Ensure that your line is fed straight through the bottom guide, and then fill your spool until there is a 1/8-inch gap (it is essential to keep tension on the line as it goes on).

The final step is to connect your braided line to your leader line. Anywhere between 6 and 9 feet should suffice. I like it because the knot doesn’t quite fit into my spool. I’ll position the knot somewhere between the lowest guide and my reel when I’m ready to cast. This ensures no friction or that nothing gets caught up when I’m casting.

Conclusion

That’s all there is to it. I’ll also add a clip to the end of my leader so I can quickly change lures while fishing. It is best for me and is a wonderful setup if you plan on fishing for a variety of species. So, enjoy your fishing; the sea is teeming with fish.

Please let me know what you think and if you have any questions. Do you like this article? Please feel free to share it!

Related Post: Best Baitcasting Reel For Frog Fishing: 6 Top Picks