How do I learn to Baitcaster (How to Use a Baitcaster)

The development of fishing equipment does not stand still, so there is more and more a wide range of kinds of fishing rods. But the Baitcasting reel seems more popular with anglers although Baitcasting reel is pretty hard for beginners in fishing.  Baitcaster appeared in the mid-17th century but was widely used by amateur anglers from the 1870s until nowadays.

Compared with spinning or spin casting reels, Baitcaster does many fishing tasks better than them. It is the reason why it is the standard gear used in fishing. Using Baitcaster can take your fishing experience to the next level. So how to use a Baitcaster to have the best experience and optimize your bass fishing? Let’s walk you through the step in this writing. 

What Are The Pieces Of Equipment We Need?

First of all, you need to prepare equipment for Baitcast to add a new fishing line to your reels effectively:

  • Rod
  • Reel
  • Monofilament fishing line
  • Braided fishing line (optional)
  • One fellow fisherman
  • Pencil

If you feel there are many things you need to prepare Baitcaster combo is the most enough choice for you.

Related Post: Best Baitcasting Reel For Beginners

How To Spool A Baitcast

After that, we need to turn on the reel properly. Learning how to fish a reel will make your overall fishing experience better. Once you’ve chosen the right line for your rod and application, you can start fishing when using monofilament or fluorocarbon (Monofilaments and fluorocarbons are polymers made by polymerizing specific monomers are mainly related to their primary application – use as fishing line. A fishing line is a thread-like structure (a line) used in fishing); the line can be tied directly to the spool. The twine is slightly different because it slides over the spool, so support is needed. Stick a layer of tape around your spool before braiding for an easy hack. For a more professional look, wrap a few knots of monofilament or fluorocarbon wire first, and then tie a single knot into your braid. The backing will grip the spool tightly, and the braid will not slip.

The Step By Step For The Spooled Up:

  1. Run the line through all the guides on the reel and the rod’s level wind guide.
  2. Bind the line around the spool and tie the Albright knot. Wet the knot and pull the mainline to tighten.
  3. Cut the card tag as close to the knot as possible.
  4. Fasten the spool the line towards the rod end so that the line out of the spool stays in the same direction as it enters the spool of the reel’s spool.
  5. Keep the tension in the line between your thumb and finger to maintain even pressure throughout the spooling.
  6. Continue winding up the spool until it is about 1/8 inch from the end of the spool

Setting & Adjusting The Reel

Once you have the spooled up, the next important step is to set up the reel. You were setting it up before transmission avoids hassles and unwanted backlash. Hold the rod up at a 2 o’clock angle, and allow the foot of the rope to hang down when casting the light lure with a Baitcaster. Tighten the tension knob of the spool and push the thumbstick. While keeping the spool with your thumb, gradually loosen the spool tension so that the lure falls to the ground taking about 3 seconds. Test it a few times to ensure that the bait drops steadily at 3 seconds. It tightens the spool tension if it accelerates and bounces back when falling. Repeat these steps each time you tie on a new bait. Otherwise, it is very easy to have an eyelid collapse.

Why do professionals cast so efficiently? Why can they skip and rush into tight spots, but you get backlash after backlash when you try? Some of them are time on the water, but some of them are reel adjustments. You will become a much more efficient angler if you loosen things up and learn to control the spool with your thumb.

Brake System Adjustments

Adjusting the brake system is essential to measure the thrust force. The dynamometer is used to measure the weight of the catch. As you have this scale, for braking, you must follow these steps:

  • Attach the spindle to the rod that you will be using for a Baitcaster. It is paramount.
  • The characteristics of the cane significantly alter the force transmitted in each case onto the line. So you need always install the gauge in the equipment that carries the last reel.
  • Once the reels are mounted, pass the line through the guides and stationary sticks (partner collaboration required).
  • Set the axis of rotation manually, and consider eye correction.
  • Place the scale at the end of the wire, provided with a plastic ring that helps us measure the peak to reach the scale when the demo jerks.
  • Use a strong pull rod and check the top of the scale.

Calibrate the brake without exceeding the desired maximum power resin ring.

Repeat several times until the brake slips at the power level you want (1/3 line resistance).

No one can become a professional fisherman if their reels do not work as expected.

And that is why one of the most valuable tools in fishing reels is the brake. Indeed, correct alignment of the reel brake is one of the key points that can differentiate between being achieved or not achieved during a day of recreational fishing.

Drag System Adjustment

The drag is a pair of friction discs inside the fishing reel.

The easiest way to apply traction on the reel or reel is to test first by pulling your rope with your hand just above the reel.

Constrict the drag on your spinning wheel by turning the front traction control knob to the right a few clicks if the line pulls out too easily. If it’s too tight, loosen the resistance by turning the crank to the left a few times. Closed-sided Spincast models typically have a top-mounted reel traction adjustment mechanism.

If you don’t feel you can judge force accurately, a small spring scale can help, such as the one used in Boca Grips or other fish handling equipment used in the catch and release process. For best results, you can keep your Baitcaster rod at a 45-degree angle and hook the weight; then, the pull setting should be at a point where the line holds one-third to one-half of its weight before moving (for example, a 20-pound line won’t move until the hook has).

You’d better pull too loose and fight a fish a little longer than let it get too tight and break a big fish.

What Is Gear Ratio, And Is It Important?

The Baitcaster gear ratio uses to determine the speed at which the spindle runs up, also known as the line recovery rate. Is it important? The gear ratio is a topic that you can make as complicated or as simple as you like. If you’re just starting, don’t worry about it. That does not matter.

Tips On How To Use A Baitcaster

The best baitcasting reel choice on the market supplies higher gear ratios, providing additional speed for faster reeling when fishing with spinnerbaits, crankbaits, and buzz baits.

Conclusion

After you get your first reel, the best thing to do is not practice in the water in your backyard or an open field. You need to focus on the reel, and it is the fastest way to get comfortable with your baitcasting reel and how it works without any distractions like fish. I like to use old, used lures for backyard casting, similar to what I would use on the water.

Related post: Top 10 Best Baitcasting Reels For Trout